Aztec Temple Sentinel Tower & a Challenge Update

In this post I will share my latest MDF kit build for Feudal Patrol games in Mesoamerica (using my Civilizations Collide supplement). I was able to finish off another Aztec-inspired MDF kit. This one also came from from Things From the Basement via 4Ground via Badger Games (see it here). It is called Temple Sentinel Tower and is scaled for 28mm figures – and is just what it is described as being – a Temple Sentinel Tower which would be a nice piece of high ground for some missile troops.

This is part of “Mark’s Aztec Building Challenge Contest” (which you will read more about shortly in this blog post), as well as the April painting challenge from Ann’s Immaterium called Ann’s “Paint the Crap You Already Own” challenge.

The kit as received.

It was an enjoyable kit to build. This one had a few challenges for the build as I needed to make sure that I could paint the inside of the tower as well as dust it up with chinchilla dust as I have been doing. I want all these cityscape Temple structures to match in character – and in color and texture. Basically, as you will see, I broke the kit into two parts until final assembly.

The kit after wiping down with a moist microfiber cloth. The instructions were good.
First day of assembly and setting up with PVA, rubber bands, and clamps.
The lower tower section is on the left – and the top here has been left to work on separately with paint and chinchilla dust as I have previously described (see this page). Having steel washers around held as weights with PVA gluing.
The tower sections awaiting base coating after dusting up with the chinchilla dust and watered down PVA slurry.
The sections after the base coat was applied and the dry brushing of the textures. The red, black, and yellow colors were painted after the dry brushing.

The finished Temple Sentinel Tower next to my previous MDF builds. I put a few missile troops up in the tower as examples.
Different angle view.
An Aztec veteran with an atlatl peers out while a macuahuitl-armed comrade guards the ladder access. A sling-armed novice is at the top of the ladder.
A close up of a bowman (front) and another slinger (left) in the tower.

I think this came out well – what do you think?

For the other pieces in the building contest, I was also able to airbrush a decent base coat on my remaining resin structures, as well as to start on the ground cover on their styrene bases.

The remaining resin structures – I have a good start on them.

This now leaves me with two more MDF builds – the Temple High Throne and the Sacrificial Altar – in addition to the resin. These are going to take a back seat to finishing the resin pieces. This is because as I have more paint on order to properly finish them similarly to my previous MDF kits. I have found that I’m going though a good amount of paints and washes (chinchilla dust and MDF can be thirsty).

I have also tried to show you, dear readers, the progress in my challenge in a non-award-winning video on IGTV and Instagram (well it hasn’t won yet, so there’s hope…).

My main communications channel is THIS BLOG! But, I’m just trying to keep up with the young ‘uns like IRO. It’s a bit of an unscripted thing – so enjoy! Without any further ado – here is the video link live from my cellar (that I cannot put on WordPress without paying more $$).

So as for the contest – I have a shot below that shows the range of guesses:

The contest IS ON! Who will win?

We’ve got American, Aussie, and Brit entries (what’s up with the rest of the world?). Thanks to all for entering and best of luck – and follow my progress (and your chances) here! The average is May 19th, with Azazel the earliest on 4/24/2021 and Ann the latest on 6/30/2021. Hell, your guesses are as good as mine at this point for sure.

A couple of small side notes. I was quite surprised and happy to see that 4Ground featured my work on their Facebook page – here is that Facebook link – and much thanks to our pal Kuribo who let me know on the blog that he saw it. Also, this marks my 30th post on this subject – and while I’m happy about the progress I’ve made – the listing of all the posts is getting to be a bit much (never mind approving all the WordPress pingbacks that this generates).

So, I’ve added a new selection on my main menu (“Gaming & Hobby Areas of Interest”), and under that will be individual genre selections. I’ve started with a page with a list of and links to all of my Mesoamerican posts called “Aztec, Conquistador, and Mesoamerican Hobby Projects Posts” – and I will (over time) be augmenting it with other stuff, such as retro sci-fi, France 1940, Normandy, etc. But I won’t get to that for a while – I’ll be focusing here on the Aztec stuff! I’ll still add the paints and materials section as before, mostly for my own references.

Thanks for looking and I hope that you can check out the video link and no matter what – let me know what you think of the tower – or my accent – or my graying hair – or whatever.

For all of my previous posts on games, units, and other projects for my 16th Century Spanish Conquest supplement for Feudal Patrol™ – “Civilizations Collide” – please see this page.

PAINTS, INKS, GLAZES, SHADES, WASHES, PIGMENTS, FLOCKING, GLUES AND MORE THAT I USED ON THESE PIECES:

  1. Elmer’s PVA Glue
  2. Poster tack
  3. Plastic Plates
  4. All Living Things Dry Dust Bath (chinchilla dust)
  5. Vallejo “Flow Improver”
  6. Vallejo “Airbrush Thinner”
  7. Vallejo Model Air “Sand (Ivory)”
  8. Vallejo Game Air “Desert Yellow”
  9. Vallejo Model Color “Dark Sand”
  10. Citadel “Ushabti Bone”
  11. DecoArt “Light Buttermilk”
  12. Vallejo Model Air “Wood”
  13. Vallejo Model Color “Red”
  14. Craftsmart “Black”
  15. Citadel “Yriel Yellow”
  16. Army Painter “Light Tone” (wash)
  17. Vallejo Game Air “Ivory”

Aztec Temple Corner Walls (Plus Some Life & Other Distractions Stuff Added In)

This blog is titled “Life, Golf, Miniatures, and Other Distractions” – and it’s not often that it’s about anything but miniatures. This post will definitely concern miniatures – but as the title suggests, a few other things are going to get added in after the miniature stuff.

Why you ask? Well, the long and short of my current predicament is that a member of my household is near the end, and I need to deal with the ramifications of that. It’s sad, but it’s time.

Oh, sorry, not a person, it’s my PC that is on its last legs – and it is already quite legless.

My PC has had multiple thermal shutdowns over the last few weeks – while in sleep mode! Argh! I decided that I would need to get a new desktop before I lose all my hobby work (plus everything else that is on the thing). I prefer a PC over a laptop, though I still look at WordPress on my iPhone and my iPad. I just compose on a PC. Anyways, I will be without a computer shortly – so I needed to get a post in. Therefore this post will cover some miniature stuff first and some fun (I think) extras – I hope that they will be somewhat interesting for you.

Plus, this is my largest list of hashtags ever (I think so anyways).

In my last post, as part of “Mark’s Aztec Building Challenge Contest” (which you should enter soon by the way!) I discussed how I assembled and painted 8 Temple Columns for my Aztec games of Feudal Patrol using my Civilizations Collide supplement.  I had moved onto the MDF kits over my resin stuff as temperatures had been too cold here in Massachusetts to use rattlecans to prime outside. I truly enjoyed building and painting the MDF of my last post, and I certainly still have a love for using chinchilla dust.

My next MDF effort would be two kits of the “Temple Corner Walls” – from Things From the Basement via 4Ground via Badger Games (see it here). Each kit had one square pillar-like structure and two walls – six in total. The kits are very nice and pretty easy to work with in my opinion. I basically used the second approach from last time – assemble first, then dust up with the chinchilla dust and paint them.

An example of one kit out of the bag after cleaning it off with a moist microfiber cloth.
I have found with these MDF kits that it helps to dry fit first and organize the parts. Here you also see that I put an “up” arrow on the inside of the walls to help make sure that I did not assemble anything upside down.
I assembled the wall sections first and let the PVA dry overnight.
The next day, I added steel washers as weight to get the wall tops to glue flush to the previous step’s work. Then I glued to the bases (with the weights again).
All of the “Temple Corner Walls” assembled and ready to get dusted up and painted.
Here you see my early dry brushing after dusting – I use three colors to dry brush. I decided to paint the triangles in a red, black, and yellow pattern. You can see the paints that I used at the very end of this post.
After I dry brushed the structures, I toned down the dry brushing with Army Painter “Light Tone”. Between the “thirst” of both the MDF and the chinchilla dust, I ended up using the better part of two bottles of the AP tone. Here, these are all complete.

I tried to use my spray booth again for some shots here but I did get some weird shadows and alternatively unwanted shine that I did not like. So I went with what you see below. I’ll need to investigate a light box (maybe).

Here you see a fight among the “Temple Column Walls” (this post) and the “Temple Columns” (from my last post) between a squad of Conquistadores (and a wardog) against an Aztec squad and a supporting warrior priest. I think that I was successful at getting all to blend in well.

So, the Temple Corner Wall structures of this post are part of two “challenges”. The first is mine as mentioned earlier – “Mark’s Aztec Building Challenge Contest” – in which I will give away free prizes to blog followers for being the closest to guess how long it will take me to finish all these buildings. The second is from Ann’s Immaterium, and is called Ann’s “Paint the Crap You Already Own” challenge. These definitely count there – and I hope there will be more for this April challenge.

I have ordered some more “Light Tone” – and with my remaining MDF I’ll need it. In the meantime, as an update – it warmed up here this week so I was also able to get my outside priming done – see below!

I was able to prime this week! I can now vary what I decide to complete.

I also am planning an update to my Civilizations Collide supplement, which will have rules for the falconet and some new scenarios (in addition to an overall update). So that might slow up my progress, as also golf might (haven’t played yet this year though). I also have been – wait for it – GAMING!

Well, remotely anyways. I was lucky enough to play in a Combat PatrolTM game last Saturday via Zoom with Sally4th’s Chris Abbey. Chris (in the UK) set up a James Bond game based on the 1977 film The Spy Who Loved Me that he called “Nobody Does it Better” (Carly Simon song of the movie). It featured the scene in the bad guy’s (Stromberg) supertanker interior hold (that held a captured US sub). The action focused on the scene where escaping British, Russian, and American crews fight the Stromberg goons to stop a nuclear launch. We had US and UK players – and I had James Bond. Our objective was to advance up the gantry and throw a satchel charge at the control room doors and blow it open. We had a lot of twists and turns in the game – James Bond’s satchel charge misfired, and so did a Stromberg flamethrower that would have fried him. A last second satchel charge throw from the Americans missed, but the explosive charge slid up to the door and blew it! Success! Notably, I had invited our blogger buddy TIM who got to watch the game – and it was fun to share the experience with him.

Take a look at the tabletop below – amazing!

The tabletop before the game.
Chris Abbey GM’s the game exceptionally well. We were moving up the gantry on the left – the control room was in the center of the far end.

I also had two other nice surprises. The first was in the mail from Buck Surdu – who sent me a couple of Wars of Ozz shirts. I did get in the Kickstarter for it (and the figures are available from Sally 4th and Old Glory in the US) -and the next project I plan to do is paint these figures.

The second surprise came in our local weekly newspaper (see below). I’ll let Andy Newton’s words speak for themselves, but given the last few months, this was a heartwarming bonus for us.

From The Spencer New Leader

And though my computer is a problem, I did get the email from the Commonwealth of Massachusetts that has allowed me and my wife to get our first “jabs” this weekend! Take that COVID-19!

So, until my computer situation is better – I’ll be painting and following up on my iPad. Maybe I’ll be back this weekend – in any case, let’s discuss this post! So feel free to let me know your thoughts and comment – and to enter the contest. Take care all and thanks for looking!

Miscellaneous details and references for those interested in that sort of thing:

Previous posts on games, units, and other projects for my 16th Century Spanish Conquest supplement for Feudal Patrol™ – “Civilizations Collide”

  1. Aztec Temple Corner Walls (Plus Some Life & Other Distractions Stuff Added In) (this post)
  2. Aztec Temple Columns and My New Love for Chinchilla Dust
  3. Mark’s Aztec Building Challenge Contest
  4. Game Aids and Tools for Feudal Patrol games using the Civilizations Collide Supplement
  5. And the Winners of “Mark’s Conquistador Contest” are…
  6. Conquistador Cavalry. 24 figures total: Outpost Wargame Services #CON5 “Conquistador Cavalry in light armour 1” (4 horses & 4 riders); Outpost Wargame Services #CON6 “Conquistador Cavalry in full armour” (4 horses & 4 riders); Eureka Miniatures “Moving Horses” #100ANM05 (8 horses used as casualty markers).
  7. Conquistador Falconet and Crew (Artillery). 3 figures total: Outpost Wargame Services #CONA1 “Falconet and Crew”.
  8. More Conquistador Sword and Buckler Men. 8 figures total Outpost Wargame Services #CON001 “Sword and Buckler Men”.
  9. Conquistador Sword and Buckler Men (Wargames Foundry). 18 figures total in three blister packs: Wargames Foundry #SB015 “Swaggering Swordsmen”, #SB016 “Brutal Sword and Buckler Men”, and #SB017 “Bold Bladesmen”.
  10. Perro de Guerra (Conquistador War Dogs). 13 figures total: Outpost Wargames Services #CONS6 “War Dogs” (8 war dogs); Eureka #100CON13 “Dog Handler and Dogs” (1 dog handler/pikeman and 4 war dogs)
  11. Conquistador Foot Command, Crossbowmen, and a Couple of Officers. 11 figures total: Outpost Wargames Services #CONC1 “Conquistador Foot Command” (a leader, a banner bearer, a drummer, and a bugler); Eureka #100CON04 “Crossbowmen” (5 crossbowmen); and Eureka CONC1 “Conquistador Officer” and an unknown SKU officer (2 officers)
  12. Merciless Adventurers (this post) – Wargames Foundry #SB014 (6 Conquistadores with arquebuses)
  13. Audacious Arquebusiers! – Wargames Foundry #SB012 (6 Conquistadores with arquebuses)
  14. Mark’s Conquistador Contest – for my loyal blog followers!
  15. Montezuma and Chieftains – Wargames Foundry #AZ011 for Feudal Patrol – 6 Aztec figures (Montezuma, 4 Chieftains, 1 Warrior Priest)
  16. Aztec Shock Troops – Cuachic Warriors aka The Shorn Ones – 8 Aztec cuachicqueh warriors
  17. Tloxtoxl and the Priests of the Great Temple, Wargames Foundry AZ021 – 2 warrior priests, 1 priestess, 1 priest, 1 leader, and 1 signaler
  18. Civilizations Collide – The Wars of the Aztecs, the Inca, the Maya, and the Conquistadores is now available as a FREE Download for Feudal Patrol™ – plus a Feudal Patrol™ review!
  19. 18 Aztec Novice Warriors for Feudal Patrol Walk into a Bar – 18 Novice Warriors
  20. Aztec Warrior Priests (painted as Tlaxcalans), Ral Partha 42-302, circa 1988 (this post) – 6 figures – 6 Tlaxcalan Warrior Priests
  21. Tlaxcalan Novices, Elite Warriors, and Command Group – 18 figures – 8 Novice Tlaxcalan Warriors, 8 Elite Tlaxcalan Warriors, 1 Tlaxcalan Captain, 1 Tlaxcalan Conch Blower
  22. Tlaxcalan Archers – 8 Veteran Tlaxcalan Archers
  23. Aztec Game for Feudal Patrol across thousands of miles – via Zoom!
  24. Aztec Snake Woman and Drummer – 1 Aztec General, 1 Aztec Drummer
  25. A June and July Jaguar Warrior Frenzy (plus some Aztec Veterans and a Warrior Priest to Boot) – 3 Aztec Veteran Warriors, 17 Jaguar Warriors, 1 Aztec Warrior Priest
  26. Doubling Down – Aztec Veteran Warriors – 24 Aztec Veteran Warriors
  27. Aztec Arrow Knights, Ral Partha circa 1988 – 6 Aztec Arrow Knights
  28. Aztec Eagle Warriors from Tin Soldier UK – 6 Aztec Eagle Knights
  29. Aztec Novice Warriors and a few Frinx – 12 Novice Warriors

PAINTS, INKS, GLAZES, SHADES, WASHES, PIGMENTS, FLOCKING, GLUES AND MORE THAT I USED ON THESE PIECES:

  1. Elmer’s PVA Glue
  2. Poster tack
  3. Plastic Plates
  4. All Living Things Dry Dust Bath (chinchilla dust)
  5. Vallejo “Flow Improver”
  6. Vallejo “Airbrush Thinner”
  7. Vallejo Model Air “Sand (Ivory)”
  8. Vallejo Model Color “Dark Sand”
  9. Citadel “Ushabti Bone”
  10. DecoArt “Buttermilk”
  11. Vallejo Model Color “Red”
  12. Americana “Kelley Green”
  13. Craftsmart “Black”
  14. Citadel “Yriel Yellow”
  15. Army Painter “Light Tone” (wash)
  16. Vallejo Game Air “Desert Yellow”

Aztec Temple Columns and My New Love for Chinchilla Dust

When one considers the Aztecs and their empire, what does the historical record say about which visual images struck the Conquistadores in 1519 with awe? Colorfully costumed and tremendously fierce warriors? Eagle Warriors? Jaguar Warriors? Montezuma II and his palace? Untold amounts of gold and silver? Perhaps their quite bloody reputation for human sacrifice, slavery, and occasional cannibalism? The magnificence of the city of Tenochtitlan and its amazing architecture? Probably all that and more, at least in what I have read.

As I shared in my last post – I am working on terrain/buildings for the period as part of “Mark’s Aztec Building Challenge Contest”. These buildings are either resin or MDF. I originally thought that I would start with the resin buildings and then move onto the MDF ones. To do that, I wanted a good primer on the resin – and the manufacturer (Acheson Creations) recommended a Rustoleum primer. This meant spray painting with the rattlecan outside safely – or doing it unsafely inside the house and provoking my lovely bride to commit several felonies upon my person due to the fumes. Well, I can’t visit her in jail during a pandemic – or from the grave – so I decided on the outside option.

However, despite one beautiful Massachusetts day in March where we saw the 70’s (that’s the low 20’s for you metric folks), it has been in the 40’s (4-9 for you metric folks) and rainy. Neither are good for outside. So, flip the order, and onto the MDF.

My experience with MDF is very limited – all I have done before is some MDF barriers that I did back in 2017. And they were not my best work IMO. All of my MDF in the challenge is supposed to be made of stone. MDF does not look like stone of course. It’s manufactured from wood dust and glue. So, what to do? First, I watched a smattering of YouTube videos on MDF kits. The best one said to wipe down MDF with a damp microfiber to clean prior to painting which was very important for paint to adhere!

I also reached out to a couple of friends – Buck Surdu (of Buck’s Blog) and The Imperfect Modeler (TIM) to seek their unbridled wisdom. Both were great – and TIM opened my eyes to a new (to me) and amazing hobby tool that I wanted to share with you all as I am in love with it.

Chinchilla dust.

Yes, I had never heard of it before either. I have a 26 year old cockatiel, no gerbils or similar. You find it in the pet store – apparently gerbils and chinchillas and similar beasties bathe in dust, not water. This stuff is very, very finely ground pumice. A bag cost me $22 , and I think its a lifetime supply! Based on TIM’s recommendations and advice, I planned to try to use it to create a stone-like look. I hoped to accomplish this by using it over a watery PVA application.

As I had two kits of the ones called “4 Temple Columns“, I thought I’d start there as it would enable me to experiment and learn for the rest of the MDF. I broke the kits into two attempts – with the first being painting and dusting the MDF on its sheet and then assembling the kit. The second attempt would be to assemble the kit first, and then dust up and paint.

The two unopened MDF kits. I decided that I would not need the columns stacked up as the single columns were sufficiently tall enough for my needs.
After wiping the kit off with a wet microfiber cloth, I had this.

As stated, my first kit attempt was to paint and flock in situ as it were. I applied a watery PVA coat to the MDF, and then lightly spooned on or pinch-applied the chinchilla dust. I tried removing excess with a reusable Testors plastic cheap brush. I did this in a plastic tub so as to minimize the mess (and avoid unnecessarily ticking off the wife with the unannounced arrival of a new beach in the cellar). This was a bit time-consuming and not very efficient I found.

Here you see the MDF sheet with the chinchilla dust bag in the back. The watery PVA glue was applied with a cheap brush, and the chinchilla dust was applied with a tiny sculpting spoon or my pinched fingers. I tapped off or brushed off any excess.

After the glue had dried, I used my cheapest airbrush (my Iwata Neo) to paint the sheet with Vallejo Model Air “Sand (Ivory)”. When that was dry and basically cured, I dry brushed the sheet serially with three colors: Vallejo Model Color “Dark Sand’, then Citadel “Ushabti Bone”, then DecoArt “Buttermilk”. I wanted to get some depth of color this way. Then I painted the idols’ faces (all paints are listed at the end of this post as references too). The main challenge I had was not to let my paints be too thin, as they could easily run via capillary action to unwanted parts of the models. Happily, the chinchilla dust is so porous that it grabs paint easily.

The MDF sheet after dry brushing the three colors over the base coat.
Here you see the idols’ images painted. I wanted them to look well-carved but painted with primitive paints.

After painting all of it, I used Army Painter “Light Tone” over the whole of both sheets.

After the wash application.

Now, it was time to assemble. the directions were easy enough – but I discovered three issues. One was that I wasted a lot of paint and effort on parts I would not need. Second, that assembly would be complicated (just slightly) by the added thickness of the painted/dusted MDF. That was easily dealt with by an Exacto blade. Thirdly, the brown (laser-burned) surfaces of the MDF would not be the same texture and color of the rest – hardly a way to look like stone. These were the surfaces I did not get to paint by leaving the pieces of MDF on the sheets. I needed to touch all of those areas up after assembly and leaving to let the glue to dry overnight.

Assembled and left to let the PVA used in assembly dry overnight.
All the brown areas needed touch up to match the rest of the pieces!
I added more chinchilla dust and repeated the previous process with paint and wash. I needed an easier way!
First group completed.
Close up of example from the first group. I would later tone them down a bit more.

Going forward, I saw opportunities to address the shortcomings from the first go -around.

First, I would assemble first, and then apply the chinchilla dust, paint and wash. This would limit the need for so much touch up. Second, I got a small spray bottle and a cheap salt shaker from Wal-Mart to respectively apply the watery PVA glue and the chinchilla dust more easily. Both were huge improvements for round two.

Round two – let’s assemble FIRST.
An example after the chinchilla dust application put on a plastic plate with poster tack in my spray booth.

I used the exact same order of paints and washes as before – and then went back afterwards with “Light Tone” to get better blending on all of them. A few bonuses here around chinchilla dust – it is so porous that it traps a lot of the paint and the wash – and it dry brushes great. You will use more paint too. Varnishing was unnecessary – a big plus!

So here are the final results:

This is a shot of the first four Temple Columns that I completed.
Here are all of the 8 Temple Columns. I used a different design top for the second set. The lighting here is making the tops look too shiny – see next shot – they are fine.
Here is a top view. The first set tops ironically looked less “seamless” than the second set.
Here you see the columns with a couple of 28mm Conquistador arquebusiers for scale comparison out of the booth.

I did use a new setup for photos here – got some black fabric to put in my spray booth, binder-clipped it, and add a flashlight – et viola. My previous Sonoran Desert background would not have worked well. I probably need to put a filter over the spray booth light next time as the light was too bright – even with editing.

It ain’t pretty, but it works.

So that’s my March 31st completion. I am hoping to add any next April-completed pieces to Ann’s “Paint the Crap You Already Own” challenge.

BIG THANKS TO BUCK AND TO TIM!

Remember to follow my blog and enter my contest! The entry window closes on midnight EDT (US East Coast time) on April 10th, 2021.

And always, I invite your feedback on this post! Thanks for taking a look!

Miscellaneous details and references for those interested in that sort of thing:

Previous posts on games, units, and other projects for my 16th Century Spanish Conquest supplement for Feudal Patrol™ – “Civilizations Collide”

  1. Aztec Temple Columns and My New Love for Chinchilla Dust (this post)
  2. Mark’s Aztec Building Challenge Contest
  3. Game Aids and Tools for Feudal Patrol games using the Civilizations Collide Supplement
  4. And the Winners of “Mark’s Conquistador Contest” are…
  5. Conquistador Cavalry. 24 figures total: Outpost Wargame Services #CON5 “Conquistador Cavalry in light armour 1” (4 horses & 4 riders); Outpost Wargame Services #CON6 “Conquistador Cavalry in full armour” (4 horses & 4 riders); Eureka Miniatures “Moving Horses” #100ANM05 (8 horses used as casualty markers).
  6. Conquistador Falconet and Crew (Artillery). 3 figures total: Outpost Wargame Services #CONA1 “Falconet and Crew”.
  7. More Conquistador Sword and Buckler Men. 8 figures total Outpost Wargame Services #CON001 “Sword and Buckler Men”.
  8. Conquistador Sword and Buckler Men (Wargames Foundry). 18 figures total in three blister packs: Wargames Foundry #SB015 “Swaggering Swordsmen”, #SB016 “Brutal Sword and Buckler Men”, and #SB017 “Bold Bladesmen”.
  9. Perro de Guerra (Conquistador War Dogs). 13 figures total: Outpost Wargames Services #CONS6 “War Dogs” (8 war dogs); Eureka #100CON13 “Dog Handler and Dogs” (1 dog handler/pikeman and 4 war dogs)
  10. Conquistador Foot Command, Crossbowmen, and a Couple of Officers. 11 figures total: Outpost Wargames Services #CONC1 “Conquistador Foot Command” (a leader, a banner bearer, a drummer, and a bugler); Eureka #100CON04 “Crossbowmen” (5 crossbowmen); and Eureka CONC1 “Conquistador Officer” and an unknown SKU officer (2 officers)
  11. Merciless Adventurers (this post) – Wargames Foundry #SB014 (6 Conquistadores with arquebuses)
  12. Audacious Arquebusiers! – Wargames Foundry #SB012 (6 Conquistadores with arquebuses)
  13. Mark’s Conquistador Contest – for my loyal blog followers!
  14. Montezuma and Chieftains – Wargames Foundry #AZ011 for Feudal Patrol – 6 Aztec figures (Montezuma, 4 Chieftains, 1 Warrior Priest)
  15. Aztec Shock Troops – Cuachic Warriors aka The Shorn Ones – 8 Aztec cuachicqueh warriors
  16. Tloxtoxl and the Priests of the Great Temple, Wargames Foundry AZ021 – 2 warrior priests, 1 priestess, 1 priest, 1 leader, and 1 signaler
  17. Civilizations Collide – The Wars of the Aztecs, the Inca, the Maya, and the Conquistadores is now available as a FREE Download for Feudal Patrol™ – plus a Feudal Patrol™ review!
  18. 18 Aztec Novice Warriors for Feudal Patrol Walk into a Bar – 18 Novice Warriors
  19. Aztec Warrior Priests (painted as Tlaxcalans), Ral Partha 42-302, circa 1988 (this post) – 6 figures – 6 Tlaxcalan Warrior Priests
  20. Tlaxcalan Novices, Elite Warriors, and Command Group – 18 figures – 8 Novice Tlaxcalan Warriors, 8 Elite Tlaxcalan Warriors, 1 Tlaxcalan Captain, 1 Tlaxcalan Conch Blower
  21. Tlaxcalan Archers – 8 Veteran Tlaxcalan Archers
  22. Aztec Game for Feudal Patrol across thousands of miles – via Zoom!
  23. Aztec Snake Woman and Drummer – 1 Aztec General, 1 Aztec Drummer
  24. A June and July Jaguar Warrior Frenzy (plus some Aztec Veterans and a Warrior Priest to Boot) – 3 Aztec Veteran Warriors, 17 Jaguar Warriors, 1 Aztec Warrior Priest
  25. Doubling Down – Aztec Veteran Warriors – 24 Aztec Veteran Warriors
  26. Aztec Arrow Knights, Ral Partha circa 1988 – 6 Aztec Arrow Knights
  27. Aztec Eagle Warriors from Tin Soldier UK – 6 Aztec Eagle Knights
  28. Aztec Novice Warriors and a few Frinx – 12 Novice Warriors

PAINTS, INKS, GLAZES, SHADES, WASHES, PIGMENTS, FLOCKING, GLUES AND MORE THAT I USED ON THESE PIECES:

  1. Elmer’s PVA Glue
  2. Poster tack
  3. Plastic Plates
  4. All Living Things Dry Dust Bath (chinchilla dust)
  5. Vallejo “Flow Improver”
  6. Vallejo “Airbrush Thinner”
  7. Vallejo Model Air “Sand (Ivory)”
  8. Vallejo Model Color “Dark Sand”
  9. Citadel “Ushabti Bone”
  10. DecoArt “Buttermilk”
  11. Army Painter “Light Tone” (wash)
  12. Vallejo Mecha Color “Off-white”
  13. Vallejo Model Color “Red”
  14. Americana “Kelley Green”
  15. Craftsmart “Black”
  16. Citadel “Yriel Yellow”
  17. Americana “Vivid Violet”
  18. Vallejo Mecha Color “Turquoise”
  19. Vallejo Game Air “Red Terracotta”
  20. Citadel “Contrast Paint – Iyanden Yellow”
  21. Craftsmart “Bahama Blue”

Mark’s Aztec Building Challenge Contest

Welcome to Mark’s Building Challenge Contest – a FREE chance for you (with no work at all except to follow my blog and guess correctly) to join me on the next leg of my Spanish Conquest journey for my 16th Century game supplement for Feudal Patrol™ – “Civilizations Collide” . Actually, as my supplement covers pre-Spanish contact, it really is a focus on Mesoamerica and South America.

The upside for you? Well, besides getting to be a follower of my blog – which I (somewhat humbly) hope is a bonus in and of itself – you will have a chance to win – yes WIN – some free stuff (miniatures or a game – see below)! This is my second giveaway contest – the first was well-received and you can see the winners here. As before, followers of this blog (either email OR WordPress) are eligible).

The upside for me is that I will get a bit more motivation to get these buildings done – and hopefully done well for the tabletop and to pass your scrutiny. Plus it will be fun. I’m hoping that I will (and many others) be able to soon get what the Brits are calling “the jab” and return to more gaming. Having these buildings done would be the icing on the cake. I also would be able to find new homes for the prizes, which are indeed nice (ask last contests’ winners Pete, Mike, and Leif).

As for this contest – read on!

Just like before, I thought this would be another way to get you involved on this project other than just reading this blog. You get to compete and guess the date that I’ll actually finish the buildings!

I am writing this on March 23rd, 2021. I have not done ANYTHING with this stuff except to take the photos of them. I’ll need to wash and assemble and paint and base and anything else I feel is needed for this stuff. My experience working with resin is ok – see here, here, and here. My experience with MDF is much less – see here. I expect to start work TODAY, March 23rd, 2021 .

How long will this take – YOU get to guess.

My goal is to have some fun, and reward my followers and share some stuff that I enjoy. Secondly, it’s to get more followers and to grow the community. Thirdly, it’s to have fun (yes that’s fun twice). I do not currently monetize my blog, and I’m not looking to anytime soon by the way. Here are the rules – please note the underlined parts:

Rules of Mark’s Aztec Building Challenge Contest:

HOW TO ENTER AND TO WIN:

  1. You must be an email or WordPress follower of my blog.
  2. You must pick a date (day, month, and year) that I will finish all of the Aztec Buildings shown here in this post.  Finishing means, to me, that I am ready for the figures to be shown on my blog and used in a game.  That is my call!
  3. You must let me know that you want in on the contest by midnight EDT (US East Coast time) on April 10th, 2021.  You do this by posting a comment that “you are in” here on this blog post in the comments section with the date information requested above in (2).
  4. Only one entry allowed per follower except as described in (5) below.
  5. If you get another person to follow my blog, you can earn another entry!  For each new follower that credits you as a referrer, you can get another entry.  All that person needs to do is comment on this post as in (3) above stating that he or she is “in” and who the referrer is.  The referrer can then reply to that comment with an additional entry date.
  6. Winners will be whoever is closest to the date I announce as the “completion date”.  That can be earlier or later – for example picking a date that is one day before is as good as if it’s one day after.  As there are multiple prizes, 1st place gets first choice, then 2nd, then third – and this time there is a 4th place! (Yes, I’m generous, eh?)   If two people pick the same date, which is possible and allowed, ties will be broken by who submitted the date first.  I reserve the right to add more prizes! 
  7. I also reserve the right to be the final judge on the contest – somebody’s gotta do that. When I finish, I will announce the winners.

So as for prizes, they will include metal miniatures, plus a brand-new shrink-wrapped unopened game is available that I will never get my wife to play – so it needs a new home. The minis are all vintage lead – and in original packaging. Great stuff I love but may not be able to paint soon – and they also deserve a home. First place gets first choice, and so on. And I will pay to ship them to the winners (including the US, UK, Australia – as long as I don’t need to hit the lottery for shipping)! So here are the current four prizes (and I may add more):

A three blister prize! Ral Partha 42-301 Aztec Generals, 42-305 Aztec Arrow Knights, and 42-309 Aztec Warriors w/Long Thrusting Spears (really tepoztopilli). 18 figures in total. All are unopened from the 1980’s. Works for 25mm or 28mm scale games.
A two blister prize! Ral Partha 42-309 Aztec Warriors w/Long Thrusting Spears (really tepoztopilli) and 42-308 Aztec Warriors w/Darts & Light Spears (really atlatl) . 12 figures total. Both are unopened from the 1980’s. Works for 25mm or 28mm scale games.
A two blister prize! Ral Partha 02-212 Savages: Bowmen (2 blisters – 12 figures total). Both are unopened from the 1990’s or early 2000’s. Works for 25mm or 28mm scale games.

Again, depending on participation and interest – I may add more. Hell, even if you win and don’t have a plan for them, these could be used as trade, or you could just tell me that “victory is enough” for you and to reward the next player or whatever you desire.

Your next questions should be – “what exactly is Mark trying to build and paint here?” and “how fast is he?”. For the second question, just check out my pages that show my previous projects. For example, 2021 is here,  2020 is here, and 2019 is here, but I list all my projects from 2016 onward under the “Miniatures and Projects” dropdown. This menu lets me track all I have done – and how, and can give you an idea.

Back to the contest. Here are the Aztec buildings (with links in the captions) of this next quest and this contest below. They are all scaled for 28mm. The resin buildings are from Acheson Creations, and there are 6 of them plus a group of scatter terrain that Acheson nicely threw in with my order. The MDF structures are creations from Things from the Basement creations via 4Ground via Badger Games. There are 7 kits of MDF.

Aztec peasant/farmers house
Aztec Noble’s house
Maize Storage Structure
Huaxtec House
Aztec Stone House
Cuezcomatl Granary Structure
This group includes several pieces of some scatter terrain that Acheson nicely threw in with my order (thank you!). I will include this as a part of the contest. There is also an African mask that I won’t include, but will likely paint for fun.
Two kits of “4 Temple Columns
Two kits of “Temple Corner Wall
One “Temple Sentinel Tower
One “Temple Sacrificial Altar
One “Temple High Throne

So, for now that’s the contest. I hope that you will enter and wish you the best of luck! Referrers are always welcome – just need to follow the rules and importantly be one of my blog followers – like the rules said!

For full disclosure, I have conferred with TIM on the resin and the MDF – and he gave me a few helpful pointers. He also pointed me in the direction of a nice Sarissa book on MDF that is very helpful. I’m sure he will join in the contest but that might change the dates you pick – or not -it’s up to you!

Stay tuned for updates as I finish pieces of this project – and I really hope that you find this fun. As I have been doing, I’ll leave a synopsis as usual like below. Stay safe and enter in the comments section!!

Miscellaneous details and references for those interested in that sort of thing:

Previous posts on games, units, and other projects for my 16th Century Spanish Conquest supplement for Feudal Patrol™ – “Civilizations Collide”

  1. Mark’s Aztec Building Challenge Contest (this post)
  2. Game Aids and Tools for Feudal Patrol games using the Civilizations Collide Supplement
  3. And the Winners of “Mark’s Conquistador Contest” are…
  4. Conquistador Cavalry. 24 figures total: Outpost Wargame Services #CON5 “Conquistador Cavalry in light armour 1” (4 horses & 4 riders); Outpost Wargame Services #CON6 “Conquistador Cavalry in full armour” (4 horses & 4 riders); Eureka Miniatures “Moving Horses” #100ANM05 (8 horses used as casualty markers).
  5. Conquistador Falconet and Crew (Artillery). 3 figures total: Outpost Wargame Services #CONA1 “Falconet and Crew”.
  6. More Conquistador Sword and Buckler Men. 8 figures total Outpost Wargame Services #CON001 “Sword and Buckler Men”.
  7. Conquistador Sword and Buckler Men (Wargames Foundry). 18 figures total in three blister packs: Wargames Foundry #SB015 “Swaggering Swordsmen”, #SB016 “Brutal Sword and Buckler Men”, and #SB017 “Bold Bladesmen”.
  8. Perro de Guerra (Conquistador War Dogs). 13 figures total: Outpost Wargames Services #CONS6 “War Dogs” (8 war dogs); Eureka #100CON13 “Dog Handler and Dogs” (1 dog handler/pikeman and 4 war dogs)
  9. Conquistador Foot Command, Crossbowmen, and a Couple of Officers. 11 figures total: Outpost Wargames Services #CONC1 “Conquistador Foot Command” (a leader, a banner bearer, a drummer, and a bugler); Eureka #100CON04 “Crossbowmen” (5 crossbowmen); and Eureka CONC1 “Conquistador Officer” and an unknown SKU officer (2 officers)
  10. Merciless Adventurers (this post) – Wargames Foundry #SB014 (6 Conquistadores with arquebuses)
  11. Audacious Arquebusiers! – Wargames Foundry #SB012 (6 Conquistadores with arquebuses)
  12. Mark’s Conquistador Contest – for my loyal blog followers!
  13. Montezuma and Chieftains – Wargames Foundry #AZ011 for Feudal Patrol – 6 Aztec figures (Montezuma, 4 Chieftains, 1 Warrior Priest)
  14. Aztec Shock Troops – Cuachic Warriors aka The Shorn Ones – 8 Aztec cuachicqueh warriors
  15. Tloxtoxl and the Priests of the Great Temple, Wargames Foundry AZ021 – 2 warrior priests, 1 priestess, 1 priest, 1 leader, and 1 signaler
  16. Civilizations Collide – The Wars of the Aztecs, the Inca, the Maya, and the Conquistadores is now available as a FREE Download for Feudal Patrol™ – plus a Feudal Patrol™ review!
  17. 18 Aztec Novice Warriors for Feudal Patrol Walk into a Bar – 18 Novice Warriors
  18. Aztec Warrior Priests (painted as Tlaxcalans), Ral Partha 42-302, circa 1988 (this post) – 6 figures – 6 Tlaxcalan Warrior Priests
  19. Tlaxcalan Novices, Elite Warriors, and Command Group – 18 figures – 8 Novice Tlaxcalan Warriors, 8 Elite Tlaxcalan Warriors, 1 Tlaxcalan Captain, 1 Tlaxcalan Conch Blower
  20. Tlaxcalan Archers – 8 Veteran Tlaxcalan Archers
  21. Aztec Game for Feudal Patrol across thousands of miles – via Zoom!
  22. Aztec Snake Woman and Drummer – 1 Aztec General, 1 Aztec Drummer
  23. A June and July Jaguar Warrior Frenzy (plus some Aztec Veterans and a Warrior Priest to Boot) – 3 Aztec Veteran Warriors, 17 Jaguar Warriors, 1 Aztec Warrior Priest
  24. Doubling Down – Aztec Veteran Warriors – 24 Aztec Veteran Warriors
  25. Aztec Arrow Knights, Ral Partha circa 1988 – 6 Aztec Arrow Knights
  26. Aztec Eagle Warriors from Tin Soldier UK – 6 Aztec Eagle Knights
  27. Aztec Novice Warriors and a few Frinx – 12 Novice Warriors

And for my blog buddy IRO, as it’s still March, here’s another t-shirt shot – well it’s still cold, so he gets a sweatshirt shot. It’s a Massachusetts outline with a Boston Bruins logo in different colors. Normally the Bruins (my favorite hockey team) colors are Black and Gold, but my lovely wife wanted me to have something other than those colors – so Red White and Blue are ok too!!

For IRO!

NOW ENTER!